Estimates only. Real concrete density varies with the mix, aggregate, moisture and steel. See the notes below.
How to calculate the weight of concrete
Three steps, and no formulas to remember.
Choose a shape
Use Slab or box for slabs, footings and walls. Use Area if you already know the square footage, Cylinder for round columns and post holes, or Volume if you know the cubic size.
Enter size and type
Fill in the dimensions, pick the concrete type and set the number of identical pieces. Choose Custom if your supplier gave you an exact density.
Read your result
The weight appears in pounds, US tons, kilograms and metric tonnes, together with the volume in cubic feet, yards and metres.
How concrete weight is worked out
Concrete is heavy, and its weight matters when you plan formwork, haul material, lift precast pieces or check what a base or deck has to carry. The calculation is always the same: find the volume, then multiply by the density.
For a rectangular slab, the volume is length × width × thickness, with the thickness converted to the same unit as the length. For a round column or post hole, it is π × (diameter ÷ 2)² × height.
Typical density of concrete
These are common planning values. The calculator uses the figures in the right-hand columns.
| Type | Typical range | Used here |
|---|---|---|
| Plain concrete, cured | About 145 lb/ft³ | 145 lb/ft³ · 2,320 kg/m³ |
| Reinforced, precast or fresh ready-mix | About 150 lb/ft³ | 150 lb/ft³ · 2,400 kg/m³ |
| Lightweight concrete | 90–115 lb/ft³ (1,440–1,840 kg/m³) | 110 lb/ft³ · 1,760 kg/m³ |
| Heavyweight concrete | 200 lb/ft³ and above | 200 lb/ft³ · 3,200 kg/m³ |
| Dry bagged mix, before water | Depends on bag weight and yield | 133 lb/ft³ · 2,130 kg/m³ |
Quick reference: common slab weights
All rows use 150 lb/ft³. Use the calculator for your exact size.
| Slab size | Volume | Weight |
|---|---|---|
| 10 ft × 10 ft × 4 in | 33.3 ft³ (1.23 yd³) | 5,000 lb (2.5 US tons) |
| 10 ft × 12 ft × 4 in | 40 ft³ (1.48 yd³) | 6,000 lb (3 US tons) |
| 12 ft × 12 ft × 4 in | 48 ft³ (1.78 yd³) | 7,200 lb (3.6 US tons) |
| 20 ft × 20 ft × 6 in | 200 ft³ (7.41 yd³) | 30,000 lb (15 US tons) |
In metric, one cubic metre of reinforced concrete weighs about 2,400 kg. A 3 m × 3 m slab that is 100 mm thick holds 0.9 m³ and weighs about 2,160 kg.
When the weight matters
- Formwork and shoring. Temporary supports must carry the full weight of wet concrete.
- Suspended slabs and decks. The structure underneath has to carry the concrete as a permanent load.
- Lifting and transport. Precast pieces, vehicle limits and crane capacity all depend on an accurate weight.
- Demolition and disposal. Skips and haulers often charge or limit loads by weight.
This calculator is a planning aid, not engineering advice. For structural design, lifting plans or load ratings, use your supplier's data and a qualified engineer.
Frequently asked questions
How much does concrete weigh per cubic foot?
Normal-weight concrete weighs about 145 to 150 pounds per cubic foot, which is roughly 2,320 to 2,400 kg per cubic metre. Plain concrete is usually taken as 145 lb/ft³ and reinforced concrete as 150 lb/ft³. Lightweight and heavyweight mixes fall well below and above that range.
How much does a cubic yard of concrete weigh?
At 150 lb/ft³, one cubic yard (27 cubic feet) weighs about 4,050 pounds, which is roughly 2 US tons or 1.8 metric tonnes. Plain concrete at 145 lb/ft³ comes to about 3,915 pounds.
How much does a cubic metre of concrete weigh?
About 2,400 kg (2.4 tonnes) for normal reinforced concrete and about 2,320 kg for plain concrete.
How much does a concrete slab weigh per square foot?
At 150 lb/ft³, a 4-inch slab weighs about 50 pounds per square foot and a 6-inch slab about 75 pounds per square foot. In metric terms a 100 mm slab weighs about 240 kg per square metre.
Is wet concrete heavier than cured concrete?
Slightly, because some of the mixing water evaporates as the concrete cures. The difference is usually small, so this calculator uses the same typical value for fresh and cured concrete. Use your supplier's data sheet if you need an exact figure.
How do I calculate concrete weight by hand?
Multiply the volume by the density. For a 10 ft by 10 ft slab that is 4 inches thick, the volume is 10 × 10 × (4 ÷ 12) = 33.33 cubic feet. At 150 lb/ft³ the weight is 33.33 × 150 = 5,000 pounds.
What does the dry bagged mix option calculate?
It uses a density of about 133 lb/ft³ (2,130 kg/m³), which comes from the bag weight divided by the yield printed on typical bagged mixes, for example an 80 lb bag that yields about 0.6 cubic feet. It estimates the weight of the dry powder before water is added. Check the bag label for the exact yield of your product.
How accurate is this calculator?
It gives a planning estimate. Real density changes with the aggregate, mix design, air content, moisture and steel. For structural design, crane lifts, transport limits or load ratings, use the figures from your supplier or a qualified engineer.
Is my data stored or uploaded?
No. The calculation runs in your browser and nothing you type is sent to a server.