Construction Tools

Soffit Vent Calculator

Find out how many soffit vents and how much ridge vent your attic needs. Enter the attic size to get the ventilation area, the length or count of vents, and a balanced intake and exhaust split.

Soffit + ridge, balanced1/150 and 1/300 rulesFree, no sign-up
Your attic
Units
The US method sizes soffit and ridge vents. The UK method sizes the eaves opening and tile vents.
The floor of the vented attic space, not the roof surface. A 30 x 40 ft house has about 1,200 ft². Use Advanced to enter length and width.
1:150 works everywhere. 1:300 needs a vapor retarder or 40 to 50% upper vents.
Intake share first. Exhaust should never exceed intake.
From the product label.
From the product label.
Both eaves added together. Checks the soffit vent fits.
Checks the ridge vent fits.

Attic size helper

Fills the attic area when both are entered.
Length x width.

Stock length and waste

Used for continuous vents only.
Typical ridge vent sections are 4 ft.
Added to the quantity you buy, not to the installed area.

Prices (optional)

Per stock piece, or per vent.
Per stock piece, or per vent.
Both eaves added together.
Under 15 degrees needs a larger opening.
Width between the eaves.
Typical value: 100 cm² (10,000 mm²).
Used if the roof needs ridge ventilation.

Last updated 4 November 2026. Based on the IRC R806 ventilation rules and typical vent data. Always check your local code and the product label.

How to use the soffit vent calculator

Four steps and no sign-up. Quick mode gives the vent area and quantity from the attic size alone. Advanced adds stock lengths, waste, prices and an attic size helper.

1

Enter the attic floor area

Multiply the length by the width of the attic floor. Use the area of the vented attic space, not the roof surface. A 30 x 40 ft house has about 1,200 ft².

2

Choose the ratio and split

Use 1:150 as the standard rule. Use 1:300 only where your code allows it. Keep the 60/40 split for more intake than exhaust, or pick another.

3

Pick your vent products

Choose a soffit vent and a ridge or roof vent. Enter the net free area (NFA) printed on each product label for an exact result.

4

Read, check the fit and order

Get the area, the length or count of each vent, the installed ratio and a fit check against your eave and ridge length. Add prices for a cost estimate.

What this calculator does that others do not

Most vent calculators stop at a single count. This one sizes both sides of the system, rounds to real product lengths and checks that the answer fits your roof.

Soffit and ridge together

Splits the required area into intake and exhaust, then sizes soffit vent and ridge or roof vent separately, including the length of ridge vent.

Real product rounding

Continuous vents are rounded up to stock pieces. Individual vents are rounded up to whole vents. The installed ratio is shown after rounding.

Code rule checks

Warns when the 1:300 conditions are not met, when exhaust exceeds intake, or when a vent will not physically fit on your eave or ridge.

Spacing and fit check

Enter eave and ridge length to see vent spacing and how much of the eave or ridge the vent needs.

What-if tables

Compare 1:150 with 1:300, different intake splits, attic sizes and vent ratings side by side.

US and UK methods

Use the IRC floor-area rule in feet or metres, or switch to the UK eaves rule for tile vents. Cost, waste and a diagram are included.

How many soffit vents do I need?

The answer depends on the size of the attic and the vent products you choose. Building codes set the total net free ventilating area (NFA), which is the open area that air can actually pass through. Soffit vents supply the intake and ridge or roof vents provide the exhaust. For a typical 1,200 ft² attic the standard 1:150 rule needs 1,152 in² of NFA, which is about 76.8 ft of 2-inch soffit strip at 9 in² per foot plus 25.6 ft of high-flow ridge vent at 18 in² per foot, with a 60/40 split.

The attic ventilation formula

  1. Required NFA (in²) = attic floor area (ft²) x 144 / ratio. The ratio is 150 for the standard rule and 300 for the reduced rule. This is the same as 1 ft² of NFA for every 150 ft² (or 300 ft²) of attic floor.
  2. Soffit (intake) NFA = required NFA x intake share.
  3. Ridge or roof (exhaust) NFA = required NFA x exhaust share.
  4. Continuous vent length (ft) = NFA needed / NFA per foot of the product.
  5. Number of individual vents = NFA needed / NFA per vent, rounded up.

Worked example: 1,200 ft² attic

Step1:150 rule1:300 rule
Total NFA1,200 x 144 / 150 = 1,152 in² (8.00 ft²)1,200 x 144 / 300 = 576 in² (4.00 ft²)
Soffit intake (60%)691.2 in²345.6 in²
Ridge exhaust (40%)460.8 in²230.4 in²
Soffit strip at 9 in² per ft76.8 ft (38.4 ft per eave)38.4 ft (19.2 ft per eave)
Ridge vent at 18 in² per ft25.6 ft12.8 ft
Ridge vent at 12 in² per ft38.4 ft19.2 ft

The 1:150 and 1:300 rules

The International Residential Code (IRC) section R806 sets the minimum net free ventilating area for vented attics at 1/150 of the area of the vented space. A reduced ratio of 1/300 is allowed when specific conditions are met.

RatioWhen it applies
1:150The default rule. Use it whenever you are unsure.
1:300Allowed where a Class I or II vapor retarder is installed on the warm-in-winter side of the ceiling in climate zones 6, 7 and 8, and/or where 40% to 50% of the required area is in upper vents placed no more than 3 ft below the ridge, with the rest at the eaves. The exact wording differs between code editions.
Check local code. Many jurisdictions amend the IRC, and the older and newer editions word the 1:300 conditions differently. Your building department decides which ratio you can use. The calculator warns you when the 40% to 50% exhaust condition is not met.

Balancing soffit intake and ridge exhaust

Ventilation works because cool air enters low at the soffits and warm air leaves high at the ridge. The two sides need to be balanced:

  • Intake should be equal to or greater than exhaust. Exhaust above intake can pull conditioned air from the house or draw rain and snow in.
  • A common target is 50% to 75% of the area at the soffit. A 60/40 intake to exhaust split is widely used and slightly pressurises the attic.
  • The ridge side needs a clear air path. Soffit vents only work if baffles keep insulation from blocking the channel above them.
Intake / exhaustSoffit NFARidge NFASoffit strip (9 in² per ft)Ridge vent (18 in² per ft)
50 / 50576.0 in²576.0 in²64.0 ft32.0 ft
60 / 40691.2 in²460.8 in²76.8 ft25.6 ft
65 / 35748.8 in²403.2 in²83.2 ft22.4 ft
70 / 30806.4 in²345.6 in²89.6 ft19.2 ft

Net free area explained

NFA is the open area of a vent after the louvers, screens and baffles are taken out. A vent that looks 16 inches wide may have far less open area than you expect. Always use the NFA printed on the product label, not the size of the vent. The values below are typical starting points only.

Vent typeRoleTypical NFA
Continuous soffit strip (2 in)IntakeAbout 9 in² per linear ft
Individual louvered soffit ventIntakeRoughly 20 to 65 in² each, depending on size
Ridge vent, standardExhaustAbout 9 to 12 in² per linear ft
Ridge vent, high-flowExhaustUp to about 18 in² per linear ft
Static box roof ventExhaustRoughly 50 to 60 in² each
Gable louver, turbine, power fanExhaustRated per product. Read the label.

Quick reference by attic size

This table uses a 60/40 split, 2-inch soffit strip at 9 in² per foot and high-flow ridge vent at 18 in² per foot.

Attic floor areaNFA at 1:150NFA at 1:300Soffit strip (1:150)Ridge vent (1:150)Ridge vent (1:300)
600 ft²576 in²288 in²38.4 ft12.8 ft6.4 ft
800 ft²768 in²384 in²51.2 ft17.1 ft8.5 ft
1,000 ft²960 in²480 in²64.0 ft21.3 ft10.7 ft
1,200 ft²1,152 in²576 in²76.8 ft25.6 ft12.8 ft
1,500 ft²1,440 in²720 in²96.0 ft32.0 ft16.0 ft
1,800 ft²1,728 in²864 in²115.2 ft38.4 ft19.2 ft
2,000 ft²1,920 in²960 in²128.0 ft42.7 ft21.3 ft
2,500 ft²2,400 in²1,200 in²160.0 ft53.3 ft26.7 ft
3,000 ft²2,880 in²1,440 in²192.0 ft64.0 ft32.0 ft

Soffit vent spacing and placement

Spread soffit vents along both eaves rather than grouping them. Place continuous strips or louvers as far out toward the fascia as possible so air reaches the whole underside of the roof, and keep every rafter bay open. For individual soffit vents, the spacing is the eave length divided by the number of vents. Enter your eave length and the calculator gives the centre-to-centre distance.

The number of individual vents depends heavily on the NFA of each one. For the 1,200 ft² attic at 1:150 and a 60/40 split, the soffit side needs 691.2 in²:

NFA per soffit ventVents neededSpacing along 60 ft of eaves
20 in²351.7 ft
30 in²242.5 ft
40 in²183.3 ft
50 in²144.3 ft
60 in²125.0 ft

How much ridge vent do I need?

Ridge vent length = exhaust NFA needed / NFA per foot of the product. A higher-rated product means less length. The ridge must be long enough to take it, and you need to stop short of the ends. If the ridge is too short, add roof vents or choose a high-flow ridge vent.

Ridge vent NFALength at 1:150 (40% exhaust)Length at 1:300 (40% exhaust)
9 in² per ft51.2 ft25.6 ft
12 in² per ft38.4 ft19.2 ft
15 in² per ft30.7 ft15.4 ft
18 in² per ft25.6 ft12.8 ft

The UK method: eaves length and roof pitch

The UK approach, as commonly summarised from BS 5250 and Approved Document C, sizes the opening along the eaves rather than the floor area. For roofs at 15 degrees or steeper a continuous 10 mm opening is used (10,000 mm² per metre of eaves), and for lower pitches a 25 mm opening (25,000 mm² per metre). Ridge ventilation of 5,000 mm² per metre is added where the pitch is over 35 degrees or the span is 10 m or more. Switch the calculation method to UK to use it with tile vents.

Installation checklist

  • Keep air flowing from soffit to ridge. Install baffles at every rafter bay so insulation cannot cover the soffit vent.
  • Keep about 1 inch of clear space between insulation and the roof sheathing in the airflow path.
  • Screen the openings. Vent openings are typically between 1/16 and 1/4 inch, and larger openings need corrosion-resistant screen or hardware cloth.
  • Seal the ceiling below. Air leaks from the house into the attic load it with warm moist air. Air-seal ceiling penetrations before adding insulation.
  • Do not duct bath fans into the attic. Vent them outdoors.
  • Cut the soffit opening cleanly and check the framing before fitting a strip.

Common attic ventilation mistakes

  • Counting the vent size instead of the NFA on the label.
  • Adding more exhaust than intake.
  • Mixing different types of exhaust vents (for example ridge vent with box vents or turbines). They can short-circuit the airflow so the soffits never draw air.
  • Blocking the soffit vents with insulation or paint.
  • Using the house footprint when the attic is smaller, or forgetting that separate attic sections each need ventilation.
  • Relying on powered fans in a leaky attic. They can pull conditioned air out of the house.
  • Using 1:300 without checking that the code conditions are met.
  • Ignoring local code or the manufacturer's installation instructions.

Climate, moisture and ice dams

In cold climates, ventilation helps keep the roof deck cold so snow melts less unevenly, which reduces ice dams, and it carries away moisture that leaks into the attic. In hot climates it lowers attic heat. In both, the biggest wins come from air sealing and insulation at the attic floor. Ventilation alone does not fix a leaky ceiling.

When you do not need attic vents

Unvented attics, where insulation such as spray foam is applied at the roof deck, have no soffit or ridge vents. They follow a different section of the code and different rules. This calculator is for vented attics. If your roof is an unvented or conditioned assembly, follow the insulation manufacturer and your local code.

Limits of this calculator

  • It is an estimate for planning and ordering. It is not a design, an inspection or a code compliance check.
  • Typical NFA values are starting points. Product ratings vary by brand and model, so use the label.
  • It assumes one vented attic space. Roofs with several separate sections need each sized on its own.
  • It does not size unvented or conditioned attics, cathedral ceilings with a different air path, or powered ventilation.
  • Codes and their editions differ by place. Confirm the ratio and conditions with your local building department.

Sources and method

The calculation follows the net free ventilating area rules of IRC section R806. The ratios, the 40% to 50% upper-vent condition, the 3 ft placement, the 1 inch clearance and the 1/16 to 1/4 inch opening size were checked against the ICC code change document for IRC R806 on 4 November 2026. The intake and exhaust balance guidance was checked against Penn State PHRC attic ventilation guidance and the Benjamin Obdyke net free area guide. Code editions are revised often, so confirm the current requirement with your local building department.

More Kalikolom construction tools: the Concrete Driveway Calculator, the Concrete Post Hole Calculator, the Concrete Weight Calculator and the Gravel Calculator. Browse all Kalikolom tools.

Frequently asked questions

How many soffit vents do I need?

It depends on the attic size, the ratio and the NFA of your vent. For a 1,200 ft² attic at 1:150 with a 60/40 split, the soffit side needs 691.2 in² of NFA. That is about 76.8 ft of 2-inch soffit strip at 9 in² per foot, or 18 individual vents rated at 40 in² each. Enter your own numbers above.

How do you calculate attic ventilation?

Multiply the attic floor area in square feet by 144 and divide by 150 (or 300 where allowed). The result is the total net free area in square inches. Then split it between intake at the soffits and exhaust at the ridge or roof, and divide each by the NFA of the vent product to get the length or number of vents.

What is the 1/150 rule for attic ventilation?

The 1/150 rule requires 1 square foot of net free ventilating area for every 150 square feet of vented attic space. It is the default rule in the IRC. A 1,200 ft² attic therefore needs 8 ft², or 1,152 in², of NFA.

What is the 1/300 rule and when can I use it?

The 1/300 rule halves the vent area. It is allowed only when conditions are met, such as a Class I or II vapor retarder on the warm side of the ceiling in climate zones 6 to 8, and/or 40% to 50% of the vent area high in the attic within 3 feet of the ridge. The wording differs between code editions, so confirm with your local building department. If you are unsure, use 1/150.

What is net free area (NFA)?

Net free area is the open area of a vent that air can pass through, after louvers, screens and baffles are taken out. It is printed on the product label or data sheet. Two vents of the same size can have very different NFA, so always use the label value.

How much NFA does a soffit vent have?

It depends on the product. A 2-inch continuous soffit strip is commonly listed at about 9 in² per linear foot. Individual louvered soffit vents vary widely, roughly 20 to 65 in² each. Use the figure on your product label and enter it in the calculator.

How do I calculate ridge vent length?

Divide the exhaust NFA needed by the NFA per foot of the ridge vent. For a 1,200 ft² attic at 1:150 and a 60/40 split, the exhaust side needs 460.8 in². A high-flow ridge vent at 18 in² per foot needs about 25.6 ft, and a standard ridge vent at 12 in² per foot needs about 38.4 ft.

How much soffit vent do I need for a 1,500 ft² attic?

At 1:150 and a 60/40 split the attic needs 1,440 in² of NFA. The soffit side takes 864 in², which is 96.0 ft of 9 in² per foot strip, or about 48.0 ft along each eave. The ridge side takes 576 in², about 32.0 ft of 18 in² per foot ridge vent.

How much ventilation does a 2,000 ft² attic need?

At 1:150, a 2,000 ft² attic needs 1,920 in² (13.3 ft²) of NFA. With a 60/40 split that is 128.0 ft of soffit strip at 9 in² per foot and 42.7 ft of ridge vent at 18 in² per foot.

What should the intake to exhaust ratio be?

Intake should be equal to or greater than exhaust. A 50/50 split is the code baseline, and many installers use 60/40 or up to about 70/30 in favour of intake. Under the 1:300 option, 40% to 50% of the area is exhaust.

Do I need soffit vents if I have a ridge vent?

Yes. A ridge vent only exhausts air. Without intake at the soffits, it has nothing to draw, and it may pull air from the house instead. The intake side should be at least equal to the exhaust side.

Can I mix ridge vents with gable vents, box vents or turbines?

It is best not to mix different types of exhaust vents. Air can enter one exhaust vent and leave another, short-circuiting the flow so the soffits do not draw air. Use one type of exhaust and put the intake at the eaves.

How far apart should soffit vents be?

Space them evenly along both eaves, with one in every few rafter bays for individual vents. The spacing is the eave length divided by the number of vents. Enter your total eave length in the calculator to get the centre-to-centre distance.

Does the attic floor area equal the house size?

Not always. The attic floor area is the area of the vented space under the roof. For a simple one-storey house it is close to the footprint, but garages, porches and separate roof sections are different. Each separately vented attic needs its own calculation.

How much space should be between insulation and the roof?

Codes call for an air space, commonly about 1 inch, between the insulation and the roof sheathing so air can flow from the soffit upward. Install baffles at each rafter bay to hold the insulation back.

Can an attic have too much ventilation?

More vent area than the minimum does not usually harm, but exhaust above intake is a problem because it can pull conditioned air from the house. Keep intake equal to or greater than exhaust, and seal air leaks in the ceiling.

Do spray foam and unvented attics need soffit vents?

No. An unvented or conditioned attic, where insulation is applied at the roof deck, follows different code rules and does not use soffit or ridge vents. Follow the insulation manufacturer and your local code. This calculator is for vented attics.

Is perforated vinyl soffit enough for intake?

Often not on its own. The holes in perforated soffit panels may not provide enough NFA, and some local inspectors do not count them. Check the product's rated NFA, and add continuous strip or louvered vents where needed.

How does the UK method differ?

The UK approach sizes the eaves opening. As commonly summarised, it is 10,000 mm² per metre of eaves for pitches of 15 degrees or more, and 25,000 mm² per metre below that. Ridge ventilation of 5,000 mm² per metre is added for pitches over 35 degrees or spans of 10 m or more.

Can I use this calculator in metric?

Yes. Switch the units to metric to enter areas in square metres, lengths in metres and vent ratings in cm² per metre or cm² per vent. The result is the same as in US units.

Why does the calculator show an installed ratio?

Vents are sold in whole pieces, so the installed area is a little more than the need. The installed ratio is the actual ratio after rounding up. It should be equal to or better than your target.

How accurate is this soffit vent calculator?

The maths is exact for the inputs. Accuracy depends on using the real NFA from your product label, the right attic area and the ratio your code allows. Treat it as a planning and ordering aid and confirm with your local building department.

Do I need a permit or inspection for vent work?

It depends on where you live and what you are changing. Re-roofing and structural changes often need a permit, and inspectors may check ventilation. Ask your local building department.