Last updated 4 November 2026. Densities are typical values and vary by source, moisture and gradation. Confirm with your supplier before you order.
Convert cubic yards to tons for gravel, sand, dirt, topsoil, mulch, concrete and more. Or go the other way and find how many yards a load of tons will fill. Pick the material, enter the amount and get the weight in US tons, metric tonnes and UK tons.
Last updated 4 November 2026. Densities are typical values and vary by source, moisture and gradation. Confirm with your supplier before you order.
Four steps and no sign-up. Quick mode needs only a material and an amount. Advanced adds moisture, compaction, waste, price and truckloads.
Choose gravel, sand, dirt, topsoil, mulch, concrete or another of the 27 materials. Not on the list? Choose Custom and enter a density.
Type the volume in cubic yards, feet or metres. Or switch to area and depth, or length, width and depth, and the calculator finds the volume.
Pick US tons (2,000 lb), metric tonnes (1,000 kg) or UK long tons (2,240 lb). The result shows all three at once.
See the weight, the density used and the order quantity. Need yards from tons instead? Tap Tons to yards at the top.
Most yards to tons converters give one number for one material. This one shows the density it used, lets you change it and covers the real-world adjustments that decide what you order.
Gravel, sand, soil, clay, mulch, concrete, asphalt and more. Each has a lighter, typical and heavier value, and the density used is always shown.
Convert yards to tons or tons to yards. Enter a volume, an area and depth, or length, width and depth.
Short tons, metric tonnes and long tons use the exact pound values, so the result is never off by the 10% that mixing them causes.
Add wet-weight, settling and spillage allowances to get the quantity you should order, not just the theoretical weight.
Enter a price per ton or per yard, a delivery fee and a truck capacity to see the cost and number of loads.
Compare materials, see the low to high density range, and check other quantities and ton types without retyping.
There is no single answer, because a cubic yard of fluffy mulch and a cubic yard of crushed rock weigh very different amounts. The weight depends on the material. As a guide, a cubic yard of dry gravel weighs about 1.42 US tons (2,835 lb) at 105 lb/ft³. That is why the common rule of thumb for gravel is about 1.4 tons per cubic yard. 10 cubic yards of the same gravel weigh about 14.18 US tons, or 12.86 metric tonnes.
Tons to yards reverses it: cubic yards = tons x pounds per ton / (density x 27).
| Step | Working | Result |
|---|---|---|
| Density | Typical dry gravel | 105 lb/ft³ |
| Per cubic yard | 105 x 27 | 2,835 lb |
| Tons per cubic yard | 2,835 / 2,000 | 1.42 US tons |
| 10 cubic yards | 10 x 1.42 | 14.18 US tons |
| In metric tonnes | 14.18 x 2,000 / 2,204.62 | 12.86 tonnes |
A gravel path 20 ft long, 3 ft wide and 4 inches deep holds 20.0 ft³, which is 0.74 cubic yards. At 105 lb/ft³ that is about 1.05 US tons. Add 10% for settling and spillage and you would order about 1.16 tons.
These are typical values for loose, delivered material. Each material has a range, so the table gives the low, typical and high end. Pick the nearest match and use your supplier figure when you have it.
| Material | Density (lb/ft³) | Tons per yd³ (low / typical / high) | Yards per US ton (typical) |
|---|---|---|---|
| Gravel (dry, ¼ to 2 in) | 95 to 115 | 1.28 / 1.42 / 1.55 | 0.71 |
| Gravel (wet) | 115 to 130 | 1.55 / 1.69 / 1.76 | 0.59 |
| Gravel with sand | 110 to 125 | 1.49 / 1.62 / 1.69 | 0.62 |
| Pea gravel | 95 to 110 | 1.28 / 1.35 / 1.49 | 0.74 |
| Crushed stone (¾ in) | 95 to 115 | 1.28 / 1.42 / 1.55 | 0.71 |
| Road base / crusher run | 115 to 135 | 1.55 / 1.69 / 1.82 | 0.59 |
| Limestone (crushed) | 85 to 110 | 1.15 / 1.28 / 1.49 | 0.78 |
| Rock (2 to 6 in) | 110 to 125 | 1.49 / 1.55 / 1.69 | 0.64 |
| Riprap | 125 to 150 | 1.69 / 1.82 / 2.03 | 0.55 |
| Crushed concrete (recycled) | 95 to 120 | 1.28 / 1.42 / 1.62 | 0.71 |
| Sand (dry) | 80 to 110 | 1.08 / 1.35 / 1.49 | 0.74 |
| Sand (damp to wet) | 100 to 125 | 1.35 / 1.55 / 1.69 | 0.64 |
| Topsoil | 80 to 105 | 1.08 / 1.28 / 1.42 | 0.78 |
| Topsoil (saturated) | 105 to 125 | 1.42 / 1.55 / 1.69 | 0.64 |
| Dirt / fill (dry, loose) | 70 to 95 | 0.95 / 1.08 / 1.28 | 0.93 |
| Dirt / fill (compacted) | 95 to 115 | 1.28 / 1.42 / 1.55 | 0.71 |
| Dirt / fill (wet) | 110 to 130 | 1.49 / 1.62 / 1.76 | 0.62 |
| Clay | 90 to 120 | 1.22 / 1.42 / 1.62 | 0.71 |
| Compost | 30 to 50 | 0.41 / 0.54 / 0.68 | 1.85 |
| Mulch (bark) | 15 to 20 | 0.20 / 0.24 / 0.27 | 4.12 |
| Mulch (wood chip) | 25 to 30 | 0.34 / 0.38 / 0.41 | 2.65 |
| Concrete | 140 to 150 | 1.89 / 1.96 / 2.03 | 0.51 |
| Asphalt (hot mix) | 140 to 155 | 1.89 / 1.96 / 2.09 | 0.51 |
| Asphalt (crushed or millings) | 115 to 145 | 1.55 / 1.76 / 1.96 | 0.57 |
| Portland cement | 85 to 95 | 1.15 / 1.22 / 1.28 | 0.82 |
| Water | 62.4 | 0.84 | 1.19 |
| Rock salt | 70 to 80 | 0.95 / 1.01 / 1.08 | 0.99 |
This table converts common volumes of dry gravel at 105 lb/ft³. For other materials, change the material in the calculator or multiply by the tons per yard from the table above.
| Cubic yards | US tons | Metric tonnes | Pounds |
|---|---|---|---|
| 1 | 1.42 | 1.29 | 2,835 |
| 2 | 2.84 | 2.57 | 5,670 |
| 3 | 4.25 | 3.86 | 8,505 |
| 4 | 5.67 | 5.14 | 11,340 |
| 5 | 7.09 | 6.43 | 14,175 |
| 10 | 14.18 | 12.86 | 28,350 |
| 15 | 21.26 | 19.29 | 42,525 |
| 20 | 28.35 | 25.72 | 56,700 |
| 25 | 35.44 | 32.15 | 70,875 |
| 30 | 42.53 | 38.58 | 85,050 |
| 50 | 70.88 | 64.30 | 141,750 |
| 100 | 141.75 | 128.59 | 283,500 |
| US tons | Cubic yards | Cubic feet |
|---|---|---|
| 1 | 0.71 | 19.0 |
| 2 | 1.41 | 38.1 |
| 3 | 2.12 | 57.1 |
| 5 | 3.53 | 95.2 |
| 10 | 7.05 | 190.5 |
| 15 | 10.58 | 285.7 |
| 20 | 14.11 | 381.0 |
| 25 | 17.64 | 476.2 |
| 50 | 35.27 | 952.4 |
| 100 | 70.55 | 1,904.8 |
Dry gravel, 105 lb/ft³, spread 4 inches deep. Multiply by a deeper layer ratio for thicker beds.
| Job | Volume | US tons |
|---|---|---|
| Path 20 x 3 ft at 4 in | 0.74 yd³ | 1.05 |
| Patio base 10 x 10 ft at 4 in | 1.23 yd³ | 1.75 |
| Garden bed 12 x 8 ft at 4 in | 1.19 yd³ | 1.68 |
| Shed base 8 x 10 ft at 4 in | 0.99 yd³ | 1.40 |
| Driveway 12 x 40 ft at 4 in | 5.93 yd³ | 8.40 |
| Driveway 12 x 100 ft at 4 in | 14.81 yd³ | 21.00 |
"Ton" means three different weights. Using the wrong one is a common source of ordering mistakes of about 10%.
| Unit | Pounds | Kilograms | Where it is used |
|---|---|---|---|
| US ton (short ton) | 2,000 | 907.18 | Gravel, soil and mulch in the USA |
| Metric tonne | 2,204.62 | 1,000 | Most countries outside the USA and UK |
| UK ton (long ton) | 2,240 | 1,016.05 | Traditional UK use |
To change between them: US tons x 0.9072 = metric tonnes, metric tonnes x 1.1023 = US tons, and long tons x 1.12 = US tons. Some converters divide by 2,200 for metric tonnes. That is a rounded figure and introduces a small error, so this calculator uses 2,204.62 lb.
Work out the volume, convert to weight, then add a margin. A typical order adds 5% to 10% for spillage and uneven ground, and 10% to 20% extra for fill that will be compacted. Most suppliers sell by the ton, so the weight matters more than the volume at the checkout. Trucks have a weight limit, and a heavy material such as wet sand or road base fills a truck by weight long before it fills it by volume. Use the truck capacity field to see how many loads you will need.
If your supplier quotes density in kilograms per cubic metre, choose Custom and select kg per m³. As a check, 1,600 kg/m³ is about 1.35 US tons per cubic yard, and 1 tonne per cubic metre is about 1.31 US tons per cubic yard. The calculator converts both for you.
The conversion uses exact unit definitions: 27 cubic feet per cubic yard, 2,000 lb per US ton, 2,204.62 lb per metric tonne and 2,240 lb per long ton. The material densities are typical industry values, cross-checked against the published tables at The Calculator Site and Inch Calculator on 4 November 2026. They are starting points and vary by source, so confirm the weight with your supplier.
More Kalikolom construction tools: the Gravel Calculator, the Concrete Weight Calculator, the Concrete Driveway Calculator, the Concrete Post Hole Calculator, the Drop Ceiling Cost Calculator and the Soffit Vent Calculator. Browse all Kalikolom tools.
It depends on the material. Dry gravel is about 1.42 US tons per cubic yard at a typical 105 lb/ft³, dry sand about 1.35, topsoil about 1.28, concrete about 1.96 and bark mulch only about 0.24. Pick your material in the calculator for the exact figure it uses.
Multiply the cubic yards by the material density in pounds per cubic foot, multiply by 27 to get pounds, then divide by 2,000 for US tons. For 10 yd³ of gravel at 105 lb/ft³ that is 10 x 105 x 27 / 2,000 = 14.18 tons.
Divide the weight in pounds by the weight of one cubic yard. For gravel at 105 lb/ft³, one cubic yard weighs 2,835 lb, so 10 US tons (20,000 lb) fill about 7.05 cubic yards. Switch the calculator to Tons to yards to do it for any material.
About 0.71 cubic yards of dry gravel make one US ton at 105 lb/ft³. That is the reverse of the usual 1.4 tons per yard rule of thumb. Wet or compacted gravel is denser, so a ton fills less space.
A cubic yard of dry gravel weighs about 2,835 lb, or 1.42 US tons. The range is roughly 1.3 to 1.55 tons depending on stone type, size and moisture. Road base and wet gravel are heavier, and pea gravel is a little lighter.
Dry sand weighs about 2,700 lb per cubic yard (1.35 US tons). Damp or wet sand is heavier, around 3,105 lb (1.55 tons), because of the water it holds.
Dry loose dirt is about 1.08 US tons per cubic yard. Topsoil is about 1.28 tons. Compacted or wet soil can reach 1.4 to 1.6 tons per yard, so the calculator has dry, compacted and wet versions.
Mulch is light. Bark mulch is about 486 lb per cubic yard, which is only 0.24 US tons, and wood chip mulch is a little heavier. Because it is so light, mulch is almost always sold by the cubic yard, not by the ton.
Concrete weighs about 3,915 lb per cubic yard, or 1.96 US tons, at 145 lb/ft³. Lightweight and heavy mixes differ. The Kalikolom Concrete Weight Calculator goes into more detail.
A cubic yard of water weighs about 1,685 lb, or 0.84 US tons, at 62.4 lb/ft³. Everything heavier than water has a density above that.
Multiply length x width x depth to get cubic feet, divide by 27 for cubic yards, then multiply by about 1.4 tons per yard. A 12 x 40 ft driveway at 4 inches deep is about 5.93 cubic yards, or 8.40 tons. Add 10% extra and choose road base for the best results.
A US ton (short ton) is 2,000 lb. A metric tonne is 1,000 kg, or 2,204.62 lb. A UK ton (long ton) is 2,240 lb. The calculator shows all three so you can match what your supplier uses.
It depends on the material. For dry gravel, one cubic yard is about 1.29 metric tonnes. A cubic yard is 0.7646 m³, so you can also convert from kg per m³ by multiplying by 0.7646 and dividing by 1,000.
It is 2,204.62 lb. Some pages round to 2,200, which makes the answer about 0.2% too high. That is small, but this calculator uses the exact value.
Real material varies with moisture, gradation, rock type and how it was loaded. A supplier weighs the actual load. Use the lighter and heavier estimates to see the spread, or enter your supplier's figure with the Custom density option.
Water adds weight but not volume. Add the moisture as a percentage in Advanced mode. For example, 10% moisture on sand at 100 lb/ft³ gives 110 lb/ft³. If you pick a wet material such as wet gravel, it already includes water, so do not add moisture again.
Loose fill settles. A common allowance is 10% to 20% for soil and road base, and less for clean stone. Enter it in Advanced mode and the calculator shows the quantity to order.
For gravel and crushed stone, multiply cubic yards by about 1.4 to 1.5. For dry sand use about 1.3 to 1.4, for topsoil about 1.2 to 1.3, for concrete about 2 and for mulch about 0.2 to 0.4. The material table above gives the details.
A US ton of dry gravel is about 0.71 cubic yards. At 2 inches deep it covers about 114 ft², at 3 inches about 76 ft² and at 4 inches about 57 ft².
Yes. Choose Area and depth, or Length, width and depth. The calculator supports feet, inches, yards, metres and centimetres, finds the volume in cubic yards, then converts it to weight.
Enter the truck capacity in Advanced mode. A tandem dump truck often carries around 10 to 14 tons, but your supplier knows the real limit. The calculator rounds up to whole loads.
Yes. Choose Custom density, enter the value and pick the unit: lb per ft³, kg per m³, lb per yd³, US tons per yd³ or tonnes per m³. This is the best option when your supplier quotes a ratio.
The maths is exact for the density you use. Accuracy then depends on how close that density is to your actual material. Treat the answer as a planning estimate and confirm with your supplier or a weigh ticket before a large order.