Madhya Pradesh · MPERC tariff 2026–27 · all 3 DISCOMs

Madhya Pradesh Electricity Bill Calculator

Choose your connection and enter your units. The calculator applies the MPERC FY 2026–27 LT tariff, including the slab-wise fixed charge, billing-days proration, Time-of-Day rates, rebates, Electricity Duty and Atal Griha Jyoti.

FY 2026–27 ratesAll LV-1 to LV-6 categoriesToD, PF, rebates and rounding
Your electricity bill
Domestic homes use LV-1.2. Shops and offices use LV-2.2. All categories are LT (low tension) with the same tariff across MP’s three DISCOMs.
Rural means areas notified by the Government of MP in 2006. Everything else is urban.
Total units for the billing period.
Days between the two meter readings. Slabs are prorated if this is not 30.
Your sanctioned load or contract demand.
Only if an inspection found more than your sanctioned load. Above 120% extra fixed charges apply.
From your bill. Billing demand is the higher of this and 90% of contract demand. Leave blank to use contract demand.
Fixed charge is billed per kW or per kVA, as set in your agreement.
Subtracted from the hours in the month for the load-factor incentive.
Smart-meter consumers get a 20% rebate on units used from 9 am to 5 pm.
Leave both ToD fields at 0 if you do not have ToD readings. All units are then billed at the normal rate.
Enter 92 or 0.92. Incentive from 86%, surcharge below 80%. Not applied to domestic.
Off-season: fixed charge on 10% of contract demand or recorded demand, energy at 120%.
Used for the assessed units of an unmetered pump.
Unmetered pumps are assessed at 95 or 170 / 180 units per HP.
Fixed charge for temporary supply is per 24 hours or part thereof.
Needs verification by the DISCOM and bills paid by the due date.
Paid per unit on the consumer’s share of the tariff.
Online rebate is 0.5% of the bill (₹5 to ₹20 for non-domestic, no cap for domestic).

Meter readings and budget (LV-1.2 domestic)

From your last bill.
The meter reading now.
Leave blank to skip.

Duty, FPPAS and other items

Defaults follow the tariff order. Change them to match your own bill.
Prompt-payment incentive applies only if you have no arrears.
State duty. 9% is the rate used by most sources; check it on your bill.
Fuel and power purchase surcharge shown on your bill. Default 0.
Only if you buy certified green energy from the DISCOM.
Arrears or any other item from your bill. The order says no meter rent is charged.

Based on the MPERC Retail Supply Tariff Order for FY 2026–27 (Annexure 2, LT tariff schedules LV-1 to LV-6). Free, no sign-up. An estimate, not your official bill.

How to calculate your Madhya Pradesh electricity bill

Pick your category, then fill in the fields that appear. Each category shows only the inputs its tariff needs.

1

Choose the category and area

Homes use LV-1.2. Shops, offices and clinics use LV-2.2. Then pick urban or rural.

2

Enter units and billing days

Enter the units for the period and the days between meter readings. The slabs are prorated if the period is not 30 days.

3

Add ToD, payment type and Advanced items

Choose how you pay. Open Advanced to set Electricity Duty, FPPAS or to use meter readings and a budget.

4

Read the breakdown

See each charge, the Atal Griha Jyoti estimate for eligible homes, and the rounded total. Print or share the result.

What makes this calculator different

It follows the tariff order line by line, including the parts that simple slab calculators leave out.

Slab-wise fixed charge

Uses the ₹81 / ₹134 per-connection charge and the ₹30 per 0.1 kW rule that depend on your total units.

Billing-days proration

Scales the slab limits when your meter reading period is not 30 days, as the order’s own example does.

Atal Griha Jyoti estimate

Shows what an eligible home may pay under the ₹1 per unit scheme, next to the tariff bill.

All LV-1 to LV-6 categories

Domestic, shops, schools, water works, LT industry, agriculture, EV charging and temporary supply.

ToD, load factor and power factor

Applies the 10% and 20% peak and 20% solar-hour rates, the 25–40% load-factor slabs and the PF table.

No wrong meter rent

The order charges no metering fee, so none is added. Rounding to the nearest rupee is applied.

How is a Madhya Pradesh electricity bill calculated?

The bill has an energy charge and a fixed charge. For homes the energy charge is telescopic, so each slab of units is billed at its own rate. The fixed charge is not telescopic: it is set by the slab your total units fall in. Adjustments for Time-of-Day, power factor, load factor and rebates follow, then Electricity Duty and any FPPAS are added and the total is rounded.

Bill = energy charge + fixed charge ± ToD and PF adjustments − incentives and rebates + Electricity Duty + FPPAS, rounded to the nearest rupee

MP electricity tariff by category, FY 2026–27

The table lists the LT categories in the MPERC order. It applies to all three DISCOMs.

CategoryGroupRates and rules

Domestic fixed charge in MP: how it really works

The fixed charge for homes is the part most online calculators get wrong. It is not one number. It changes with your total monthly units.

Units in the monthUrban fixed chargeRural fixed charge
Up to 50₹81 per connection₹67 per connection
51 to 150₹134 per connection₹111 per connection
151 to 300₹30 for each 0.1 kW₹28 for each 0.1 kW
Above 300₹30 for each 0.1 kW₹28 for each 0.1 kW

For the last two rows, every 15 units or part of 15 units counts as 0.1 kW. Consumption of 155 units counts as 1.1 kW, and 350 units counts as 2.4 kW, as the order explains.

Domestic bills for common monthly units

The table uses LV-1.2 with 9% Electricity Duty, no subsidy and a postpaid meter, over 30 days.

UnitsUrban fixedUrban billRural fixedRural bill

Worked example: urban home, 200 units

LineWorkingAmount
Energy, first 50 units50 × ₹4.71₹235.50
Energy, 51 to 150100 × ₹5.67₹567.00
Energy, 151 to 20050 × ₹7.05₹352.50
Fixed charge200 ÷ 15 = 14 blocks, 1.4 kW × ₹30 per 0.1 kW₹420.00
Electricity Duty9% of ₹1,155.00 energy charge₹103.95
TotalRounded to the nearest rupee₹1,679

Atal Griha Jyoti Yojana

State government statements describe the scheme as giving domestic consumers who use up to 150 units a month the first 100 units at ₹1 per unit, with the state paying the rest. Units above 100 and up to 150 are billed at the normal rate, and above 150 units the subsidy does not apply. Because it comes from the state, not MPERC, the calculator keeps the tariff bill and shows the scheme as a separate estimate.

UnitsTariff billWith Atal Griha Jyoti (estimate)

Billing days and slab proration

If your meter readings are not 30 days apart, MPERC prorates the slab limits. In the order’s example, 450 units over 36 days is billed as 60 units in the first slab, 120 in the second, 180 in the third and 90 above. The calculator does the same when you change the billing days.

Time-of-Day windows

ConsumerPeak (6–9 am, 5–10 pm)Solar hours (9 am–5 pm)Other hours
LV-1 and LV-3, load above 10 kW+10%−20%Normal
LV-2 and LV-4, load above 10 kW+20%−20%Normal
Smart meter, load up to 10 kWNormal−20%Normal
LV-6 EV charging+20% (all hours outside 9 am–5 pm)−20%+20%
LV-5 agricultureToD does not apply

Rebates, incentives and surcharges

ItemWhoAmount
Prepaid meterAll LT₹0.25 per unit off the energy charge
Online paymentAll LT0.5% of the bill; ₹5 to ₹20 for non-domestic, no cap for domestic
Prompt paymentBills of ₹10,000 or more0.5% if paid at least 7 days before the due date, no arrears
Load-factor incentiveDemand-based12 paise above 25% load factor, a further 24 paise above 30% and 36 paise above 40%, on units over each threshold
Power-factor incentiveNot domestic0.5% at 86% rising to 5% at 95% and 10% at 100%
Power-factor surchargeNot domestic1% at 79% rising to 5% at 75%, 10% at 71% or below
Energy-saving devicesLV-3 and LV-55% of energy charge for LV-3; 15, 30 or 45 paise per unit for pumps
Delayed paymentAll1.25% per month on the outstanding amount (not in the estimate)

Demand-based categories

Billing demand is the recorded maximum demand or 90% of contract demand, whichever is higher, rounded to the nearest whole number. If the recorded demand goes above 120% of contract demand, the extra up to 130% pays 1.3 times the fixed rate and anything above 130% pays 2 times. Energy charges are not increased. Loads of 10 kW or less normally use the load-based rows, and demand-based billing is mandatory above 10 kW for LV-2 and for all LV-4 industry.

Common mistakes in MP bill calculators

A flat ₹81 fixed charge

₹81 applies only up to 50 units. At 100 units it is ₹134, and at 200 units it is ₹420 in urban areas.

Adding meter rent

The tariff order says no metering charges are levied, so ₹10 meter rent does not belong on the bill.

Ignoring the 15-unit rule

Above 150 units the fixed charge follows each 15 units as 0.1 kW, not a single connection charge.

Using one rate for everything

Shops with up to 50 units pay ₹6.80 on all units, but above 50 units ₹8.30 applies to every unit.

Skipping rural rates

Rural fixed charges are lower, and the rural flat rate for unmetered homes is a different calculation.

Forgetting rounding and subsidies

Bills are rounded to the nearest rupee, and eligible homes may pay far less under Atal Griha Jyoti.

MP’s three distribution companies

Madhya Pradesh Paschim Kshetra Vidyut Vitaran Company (MPPKVVCL, Indore) serves the west, Madhya Kshetra (MPMKVVCL, Bhopal) serves the centre and Poorv Kshetra (MPPoKVVCL, Jabalpur) serves the east. MPERC sets one retail tariff, so all three charge the same rates.

Limits and assumptions

Electricity Duty

The duty is a state levy outside the tariff order. The calculator assumes 9% of the energy charge and lets you change it.

Atal Griha Jyoti

The scheme is announced by the state. The treatment of units 101 to 150 is an estimate and can change.

Excess demand

The 120% and 130% excess-demand rule is applied as written. Check your bill if you exceed contract demand.

Load factor

Load factor uses units ÷ (hours × the higher of recorded and contract demand), rounded down, as in the order.

Not included

HT and EHT tariffs, open access, net metering, standby charges, delayed-payment surcharge and security deposit.

Seasonal and temporary supply

Temporary rates are included for construction, events and non-domestic use. Check the order for other cases.

Ways to lower an MP electricity bill

Watch the 150-unit mark

Crossing 150 units switches the fixed charge to the per-0.1 kW rule and removes Atal Griha Jyoti eligibility.

Use daytime hours with a smart meter

Units from 9 am to 5 pm cost 20% less with ToD or a smart meter.

Pay online or go prepaid

Online payment earns 0.5% and prepaid meters give ₹0.25 per unit off.

Keep power factor high

Non-domestic and industrial connections earn up to 10% back on energy charges.

Right-size contract demand

For demand-based billing you pay on at least 90% of contract demand every month.

Consider rooftop solar

MP has strong sunshine, and net metering can cut the units you buy.

Official tariff source

Madhya Pradesh Electricity Regulatory Commission, ARR for FY 2026–27 and Retail Supply Tariff Order for FY 2026–27, Annexure 2 (Tariff Schedules for Low Tension Consumers, LV-1 to LV-6, with the General Terms and Conditions). Atal Griha Jyoti details are from state government and DISCOM statements.

Frequently asked questions

How is a Madhya Pradesh electricity bill calculated?

An MP bill adds a telescopic energy charge and a fixed charge, then applies Time-of-Day, power-factor, load-factor and rebate adjustments, adds Electricity Duty and any FPPAS, and rounds the total to the nearest rupee. For homes (LV-1.2) the energy rates are ₹4.71, ₹5.67, ₹7.05 and ₹7.24 per unit for 0–50, 51–150, 151–300 and above 300 units.

What is the electricity rate per unit in MP for 2026–27?

For LV-1.2 domestic the MPERC rates are ₹4.71 up to 50 units, ₹5.67 for 51–150, ₹7.05 for 151–300 and ₹7.24 above 300 units, each charged only for the units in that slab. LV-1.1 (up to 100 W and 30 units) is ₹3.72 per unit. Non-domestic shops pay ₹6.80 or ₹8.30 per unit on all units depending on whether they use more than 50 units.

How is the domestic fixed charge calculated in MP?

It depends on your total units. Up to 50 units the fixed charge is ₹81 (urban) or ₹67 (rural) per connection. For 51 to 150 units it is ₹134 or ₹111. Above 150 units it is ₹30 (urban) or ₹28 (rural) for each 0.1 kW, counting every 15 units or part of 15 as 0.1 kW. So 200 units means 1.4 kW and a fixed charge of ₹420 in urban areas.

How much is the electricity bill for 100, 200 and 300 units in MP?

With 9% Electricity Duty and no subsidy, an urban home pays about ₹700 for 100 units, ₹1,679 for 200 units and ₹2,627 for 300 units. A rural home pays about ₹677, ₹1,651 and ₹2,587. The calculator shows every line so you can check them.

What is the Atal Griha Jyoti Yojana and is it in the calculator?

Under Atal Griha Jyoti, state government statements say domestic consumers using up to 150 units a month pay ₹1 per unit for the first 100 units, with the rest up to 150 units at the normal rate. The scheme is run by the state, not MPERC, so the calculator shows it as a separate estimate under your result instead of changing the tariff bill.

Is there meter rent in the Madhya Pradesh tariff?

No. The MPERC tariff order for FY 2026–27 says no metering charges are levied. Calculators that add ₹10 meter rent to the bill overstate it.

What is Electricity Duty on an MP bill?

Electricity Duty is a state levy under the Madhya Pradesh Electricity Duty Act and is not part of the MPERC tariff. The calculator assumes 9% of the energy charge, which is the rate most sources use, and lets you change it in Advanced mode to match your bill.

What is FPPAS on my MP electricity bill?

FPPAS is the fuel and power purchase price adjustment surcharge. It is announced separately by the DISCOMs, can change month to month and is a percentage of the energy charge. Enter the percentage from your bill in Advanced mode.

What is the Time-of-Day (ToD) tariff in Madhya Pradesh?

Consumers with a load above 10 kW pay a surcharge on units used during peak hours (6–9 am and 5–10 pm), 10% for homes and water works and 20% for non-domestic and industry, and get a 20% rebate for 9 am to 5 pm. Consumers up to 10 kW with a smart meter get only the 20% rebate for 9 am to 5 pm. Agriculture is exempt.

What rebates can I get on an MP electricity bill?

Prepaid consumers get ₹0.25 per unit off the energy charge. Paying online earns 0.5% of the bill, with no cap for homes and ₹5 to ₹20 for others. Consumers with bills of ₹10,000 or more who pay 7 days before the due date and have no arrears get 0.5%. Demand-based consumers can earn a load-factor incentive and a power-factor incentive.

Which areas of MP are rural and which are urban for tariff?

Rural areas are those notified by the Government of Madhya Pradesh in March 2006, and all other areas are urban. Rural homes have lower fixed charges but the same energy rates.

Do MPPKVVCL, MPMKVVCL and MPPoKVVCL charge different rates?

No. MPERC issues one retail tariff for all three distribution companies: Paschim Kshetra (Indore), Madhya Kshetra (Bhopal) and Poorv Kshetra (Jabalpur). The same calculator works for all of them.

Why is my MP bill a whole rupee amount?

The tariff order says every bill is rounded to the nearest rupee: up to 49 paise is dropped and 50 paise or more goes up. The calculator shows the rounding as its own line.

Does this calculator cover HT consumers?

This version covers LV (low tension) categories LV-1 to LV-6 from the MPERC LT tariff schedules. HT and EHT tariffs are in a separate annexure and are not included yet.

Is this the same as my official bill?

No. It is an estimate. Your bill can differ because of billing days, FPPAS, arrears, subsidy changes announced by the state and the exact duty rate on your connection.

Explore Electricity Bill Calculators by State & Union Territory

Calculate your electricity bill using the latest applicable tariff rates for your region. Select your state or union territory below to access a dedicated electricity bill calculator with region-specific rates and charges.

Electricity Board Wise Calculators